The peculiar way that
an inchworm inches along a surface may not be fast compared to using
legs, wings, or wheels, but it does have advantages when it comes to
maneuvering in small spaces. This is one of the reasons why researchers
have designed and built a soft, worm-like robot that moves with a
typical inchworm gait, pulling its body up and extending it forward to
navigate its environment. The robots could one day be used in rescue and
reconnaissance missions in places that are inaccessible to humans or
larger robots.
Read more at: http://phys.org/news/2014-11-robot-inchworm-robots.html#jCp
Read more at: http://phys.org/news/2014-11-robot-inchworm-robots.html#jCp
Read more at: http://phys.org/news/2014-11-robot-inchworm-robots.html#jCp
Read more at: http://phys.org/news/2014-11-robot-inchworm-robots.html#jCp
(a) A real inchworm, (b) side view sketch of an inchworm and (c) sketch
of its main muscular structures. Credit: Wang, et al. ©2014 IOP
Publishing
The peculiar way that an inchworm inches along a surface may not be fast
compared to using legs, wings, or wheels, but it does have advantages
when it comes to maneuvering in small spaces. This is one of the reasons
why researchers have designed and built a soft, worm-like robot that
moves with a typical inchworm gait, pulling its body up and extending it
forward to navigate its environment. The robots could one day be used
in rescue and reconnaissance missions in places that are inaccessible to
humans or larger robots.
The researchers, Wei Wang, et al., at
Seoul National University in South Korea, have published their paper on the
inchworm-inspired robot in a recent issue of Bioinspiration &
Biomimetics.
In nature, the inchworm is the larvae
phase of the geometer moth and measures about an inch or two long. The small
green worm has two or three legs near its front, and two or three
foot-like structures called "prolegs" at its rear end. Although they
don't have bones, inchworms have complex muscle systems that allow them to
perform a variety of body movements, including standing up
vertically on their back prolegs.
To mimic the inchworm, the researchers
used the soft, highly flexible silicone material PDMS for the robot's body. The
researchers built an inchworm mold using a 3D printer, and then poured PDMS
solution into the mold. Then they glued small pieces of polyimide film to make
feet at the front and rear ends. To play the role of muscle fibers, the
researchers used eight longitudinal shape memory alloy (SMA) wires that extend
throughout the inchworm robot's body.
By actuating the SMA wires with
electric currents, the researchers could cause the inchworm robot's body to
move with a natural inchworm gait. Actuating the SMA wires symmetrically causes
the robot's body to contract symmetrically, resulting in linear motion.
Asymmetrical actuation results in asymmetric deformation and a turning
locomotion using one foot as an anchor. In the inchworm gait, the feet must
continually change from being used as anchors to sliding in order to generate
the push-pull motion. The researchers used alternating low-friction and high-friction
foot segments to replicate these foot changes.
Locomotion of the inchworm-inspired
robot. The back and front views show the configuration of the feet at each step
throughout the stride. Credit: Wang, et al. ©2014 IOP Publishing
Tests showed that the inchworm robot
achieves a stride length of 54 mm (about 2 inches), which is about one-third of
its body length, at a speed of about 3.6 mm/s. Turning is slower and more
complicated, requiring 21 strides to complete a 90-degree turn. Still, this
performance marks an improvement, both in stride length and turning angle,
compared to previous similar robots.
No comments:
Post a Comment